汽配人首頁 > 問答首頁

求起重吊車常用術語中英對照

有的發給我。謝謝: 問提問者：網友 | 2017-01-24

最佳回答

起升機構 Hoisting Mechanism變幅機構 Luffing Mechanism回轉機構 Swing Mechanism合格證明 Conformity Certificate 試驗報告 Test Report制造單位 Manufacture Company 設計單位 Design Institute型式 Type型號 Model 規格Specification編號 Serial No.樣機 Sample Vehicle基本臂 Basic Jib主臂 Main Jib吊臂 Suspension Arm支腿 Outrigger主鉤 Main Hook空載 Idle Load滿載 Full Load起臂 Rise Arm 落臂 Descend Arm 伸臂 Extend Arm 縮臂 Retract Arm回轉速度 Rotating Speed 總長 Total Length總寬 Total Breadth總高 Total Height軸距 Wheelbase輪距 Tread 前懸 Front Overhang后懸 Rear Overhang前伸 Front Protraction 后伸 Rear Protraction接近角 Approach Angle離去角 Departure Angle最小轉彎直徑 Minimum Diameter Of Turning Circle最小離地間隙 Minimum Ground Clearance前軸 Front Axle后軸 Rear Axle底盤 Chassis 軸數 Number Of Axles驅動型式 Driving Type排量 Swept Volume最大扭距 Maximum Torque排氣管 Exhaust Pipe發動機 Engine 變速器 Speed Changer 前進檔 Forward Gears離合器 Clutch 速比 Speed Ratio主減速比 Final Ratio轉向器 Redirector轉向型式 Steering Type制動系統 Braking System制動力 Brake Force車身 Vehicle Body油泵 Oil Pump起升馬達 Hoisting Motor回轉馬達 Swing Motor回轉支承 Pivoting Support變幅缸 Amplitude Cylinder伸縮缸 Telescoping Cylinder支腿缸 Outrigger Cylinder上車操縱閥 Aboard Control Valve取力器 Power Takeoff吊鉤 Crane Hook鋼絲繩 Steel Wire Rope力矩限制器 Load Moment Limiter吊臂 Suspension Arm許用應力值 Allowable Stress Value溢流閥 Overflow Valve臂架 Arm Suppor T主桿 Main Post潤滑油 Lubricating Oil潤滑脂 Grease Lubricant液壓油 Hydraulic Oil地磅 Loadometer酒精 Alcohol丙酮 Acetone打磨機 Polisher接線板 Terminal Board萬用表 Multi-Meter封存 Seal Up For Keeping自檢報告 Self-Check Report合格證明 Conformity Certificate力矩限制器檢測報告 Load Moment Limiter高度限位器 Height Limitator水平儀 Gradienter風速儀Anemoscope工作機構 Working Mechanism操縱機構 Control Mechanism 電氣和控制系統 Electrical And Control System滑輪 Pulley吊具 Hanger高強度螺栓 High Strength Bolt主要總成明細表 Principal Assembly List手拉葫蘆hand chain hoist手拉葫蘆例句Upside-down method using hand chain hoist for the installation of steel oil tank with an inner floating drum 手拉葫蘆提升倒裝法制安內浮頂鋼制油罐冶金起重機metallurgical crane 冶金起重機Application of 3D hook positioning and measuring device to metallurgical crane 吊鉤三維定位檢測裝置在冶金起重機上的應用 The application of bearing with inserted graphite to large metallurgical crane 鑲嵌石墨軸承在大型冶金起重機上的應用運行式起重機:TRAVELLING CRANE 運行式起重機例句:AutoCAD based TRAVELLING CRANE design system 基于AutoCAD的運行式起重機設計系統輪胎起重機 wheel crane或tyre crane輪胎起重機例句Design of Gearbox in Travel Par Wheel Crane 輪胎起重機行走部分變速箱的設計The Parametric Structure Calculation and Analysis Platform of Lattice Mobile Port Tyre Crane 格構式動臂港口輪胎起重機結構參數化計算分析平臺防爆起重機explosion-proof crane 防爆起重機例句Further Improvement on Explosion-Proof Crane 防爆起重機的進一步完善夾鉗起重機 crane with tongs或clamping crane或soaking-pit crane 夾鉗起重機英語INNOVATION DESIGN FOR THE CRANE WITH TONGS 夾鉗起重機(鉗吊)的更新改造設計Cracks have been observed on clamp arms of an imported 94t electric clamping crane after 4 years of service. 從國外購買的94t電動式夾鉗起重機，在使用4年后夾鉗鉗臂產生裂紋。The clamping device of soaking-pit crane 夾鉗起重機的夾鉗裝置移動式起重機 mobile crane或traveling crane移動式起重機英文The rental rates investigation of global mobile cranes of 2008: 回答者：網友

產品精選

我來回答